Reliability analysis of stochastic structural system considering static strength, stiffness and fatigue

Multi-failures are possible to appear in the process of using the structural system, such as dead load failure, fatigue failure and stiffness failure. The expression of residual resistance is given based on the impact of random crack propagation in- duced by the fatigue load on the critical limit stress and section modulus in this paper. The failure modes of every element of the structural system are analyzed under dead and fatigue loads, and the influence of the correlation of failure modes on reliability of the element is considered. Failure mechanism and the correlation of failure modes under dead and fatigue loads are discussed, and the method of reli- ability analysis considering static strength, fatigue and stiffness is given. A nu- merical example is analyzed, which indicates that the failure probability is different for different use life and the influence of dead and fatigue loads on reliability of the structural system is different as well. This method of reliability analysis, in the pa- per, is better than the method only considering a single factor (or static strength, or fatigue, or stiffness, etc.) in the case of practical engineering.     

Fracture of model polyurethane elastomeric networks

Fracture properties of model elastomeric networks of polyurethane have been investigated with a double‐edge notch geometry. The networks were synthesized from monodisperse end‐functionalized polypropylene glycol precursors and a trifunctional isocyanate. All reagents were carefully purified and nearly defect‐free ideal networks were prepared at a stoichiometry very close to the theoretical one. Three networks were prepared: an unentangled network of short chains (M_n = 4 kg mol^?1), an entangled network of longer chains (M_n = 8 kg mol^?1) and a bimodal network with 8 kg mol^?1 and 1 kg mol^?1 chains. The presence of entanglements was found to increase significantly the toughness of the rubber, in particular at room temperature, relative to the bimodal networks and to the short chains network. Fracture experiments were carried out at different strain rates and temperatures and showed for all three networks a marked decrease in fracture toughness with increasing temperature and decreasing strain rate which mirrored reasonably well the rate and temperature dependence of tan δ, the dissipative factor. However the proportionality factor between tan δ, and G_IC was very material dependent and the shift factors obtained for the master curves of the viscoelastic properties could not be used to build fracture energy master curves. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Aspects of fatigue failure mechanisms in polymer fuel cell membranes

The swelling‐driven fatigue behavior of polymer fuel cell membranes during relative humidity (RH) cycling is investigated. In particular, swelling‐induced membrane stresses are obtained from a numerical model simulating fuel cell RH cycle tests, and compared to the lifetimes obtained experimentally from tests conducted in the absence of electrochemical effects. A strong correlation between the lifetimes of the membranes in the actual tests and model results is obtained. In general, higher RH (or swelling) amplitude results in larger stress amplitudes and shorter lifetime, that is, fewer cycles to failure. Tensile stresses are needed for forming local cavities in the membrane, which may eventually lead to craze formation. Cavitation is less likely to occur in compressed membrane at high humidities. The stress–lifetime plots for polymer fuel cell membranes exhibit similar features to those observed for other polymers. The crazing criterion for polymers suggests that craze initiation during RH cycling is more likely to occur in the low compression regions, such as under the channels, which is in agreement with experimental observations. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1506–1517, 2011     

Reliability tests for Weibull distribution with variational shape parameter based on sudden death lifetime data

In the traditional design of reliability tests for assuring the mean time to failure (MTTF) in Weibull distribution with shape and scale parameters, it has been assumed that the shape parameter in the acceptable and rejectable populations is the same fixed number. For the purpose of expanding applicability of the reliability testing, Hisada and Arizono have developed a reliability sampling scheme for assuring MTTF in the Weibull distribution under the conditions that shape parameters in the both populations do not necessarily coincide, and are specified as interval values, respectively. Then, their reliability test is designed using the complete lifetime data. In general, the reliability testing based on the complete lifetime data requires the long testing time. As a consequence, the testing cost becomes sometimes expensive. In this paper, for the purpose of an economical plan of the reliability test, we consider the sudden death procedure for assuring MTTF in Weibull distribution with variational shape parameter.     

RELIABILITY ASSESSMENT OF STRUCTURAL SYSTEMS BASED ON DIRECTIONAL VECTOR SIMULATION TECHNIQUE

The new improved directional vector simulation method for analyzing the reliability of structural systems failure probability is researched. This paper also points out the defects of general directional vector simulation, and gives rise to a new higher accuracy approximate integral formula of structural systems failure probability. A new geometric meaning of characteristic function is obtained. A new simple method of generating uniformly distributed random vector samples inn-dimensional unit hyper-spherical surface is put forward and strictly proved. This method is easy to put into practice. Numerical examples are given to show the applicability and effectiveness of the suggested approach to structural systems reliability problems. Supported by Chinese Postdoctor Fund([1998]6, 23).     

Fracture in Ceramic-Matrix Composites Reinforced with Strongly Bonded Metal Particles

The resistance of a ceramic matrix composite to the cleavage cracking across a field of strongly bonded, uniformly distributed metal particles is studied. The crack trapping and bridging effects of the metal particles are analyzed by means of calculating the strain energy and the traction work. An explicit expression for the critical energy release rate as a function of particle volume fraction has been obtained. The fracture resistance is independent of elastic properties of the matrix and the sample geometry and is predominantly determined by the size/spacing ratio of the particles. It is shown that the theoretical curves agree with experimental data quite well. The methodology developed in this article can be used in studying the fracture resistances of composites with high filler contents and irregular filler geometries.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 303–318, May–June, 2005.     

Prediction of yield and long‐term failure of oriented polypropylene: Kinetics and anisotropy

The time‐dependent yield and failure behavior of off‐axis loaded uniaxially oriented polypropylene tape is investigated. The yield and failure behavior is described with an anisotropic viscoplastic model. A viscoplastic flow rule is used with an equivalent stress, based on Hill's anisotropic yield criterion, and the Eyring flow theory combined with a critical equivalent strain definition. This model is based on factorization of the rate and draw ratio dependence and is capable of quantitatively predicting the rate, angle and draw ratio dependence of the yield stress as well as time‐to‐failure in various off‐axis tensile loading conditions characterized solely from the transverse direction. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2026–2035, 2009     

氧自由基与心血管疾病

随着氧自由基（ＯＦＲ）在疾病中的研究日趋深入，大量的资料证实氧自由基与充血性心力衰竭，动脉粥样硬化、心肌缺血、心律失常及淋巴细胞与心力衰竭的关系诸方面的发生，发匀有密切关系。     

修理设备可更换且修理有延迟的两不同型部件并联可修系统

假定部件的寿命服从指数分布,其修理延迟时间和修理时间均服从一般分布,并且修理设备的寿命服从指数分布,其更换时间服从一般分布,利用马尔可夫更新过程理论和一种新的分解方法,研究了修理设备可更换且修理有延迟的两不同型部件并联可修系统,求得了系统和修理设备有关可靠性指标的一系列结果.     

Ply-by-Ply Failure Analysis of Laminates Under Dynamic Loading

Ply-by-ply failure analysis of symmetric and anti-symmetric laminates under uniform sinusoidal transverse dynamic loading is performed for a specified duration. The study investigates the first ply failure load, followed by the detection of successive ply failures along with their failure modes using various failure theories. Some of the well-established failure theories, mostly used by the researchers, are considered for the failure prediction in laminates. The finite element computational model based on higher order shear deformation displacement field is used for the failure analysis and the complete methodology is computer coded using FORTRAN. The ply-discount stiffness reduction scheme is employed to modify the material properties of the failed lamina. The failure theories used in the analysis are compared according to their ability to predict failure load, failed ply, failure mode and progression of failure. The failure analysis is performed for both the cross-ply and angle-ply laminates with all edges simply supported and clamped. The significance of fibre orientation and stacking sequence in terms of the strength of a laminate and failure progression is also highlighted.